language

产品管理

全部
产品管理

Home

Silicon core pipe fittings

Designed according to JT/T496-2004 and Q/KL012-2005, it is used for fastening and sealing cables in silicon core pipes.

E-mail: lcsy365@126.com

Phone/WhatsApp: +86-13807214678

Get A Quote

Online Inquiry

Product Description

Specification of silicon core pipe cable stopper

1、 Purpose

Designed according to JT/T496-2004 and Q/KL012-2005, it is used for fastening and sealing cables in silicon core pipes.

2、 Product diagram 3

3、 Composition and material

Assemble the connection according to the connection sequence.

Connection sequence:

Half round screw AB, rubber sealing ring, inner rubber gasket, moving washer AB, half round nut AB

Material Science:

ABS rubber ABS

It consists of eight parts in total.

4、 Technical requirements

Technical requirements for protective plug of silicon core pipe

Specification items	40/33
Appearance	The inner and outer walls shall be smooth and flat without cracks and obvious marks. The gate and overflow edge shall be trimmed and flat.
Material Science	ABS plastic and rubber
Outer diameter of connecting pipe (mm)	40^+0.8

5、 Installation instructions

1. Both ends of the pipe shall be cut flat and cleaned;

2. Assemble the cable stopper according to the assembly sequence;

3. First unscrew the cable stopper and put it into the silicon core tube, then tighten it to reach the best condition;

4. The cable stopper can be disassembled for many times. After a long time of use, remove the cable stopper. When reassembling, please carefully check the effectiveness of various components. If any damage is found, replace it.

Specification of silicon core pipe joint

1、 Purpose

Designed according to JT/T496-2004 and Q/KL020-2005, it is used for silicon core pipe connection.

2、 Product diagram 2

3、 Composition and material

Assemble the connection according to the connection sequence.

Connection sequence:

End cap, elastic snap ring, washer, rubber seal ring, connecting screw rod, rubber seal ring, washer, elastic snap ring, end cap

Material Science:

ABS ABS rubber ABS rubber parts ABS ABS ABS

There are nine parts and five varieties in total.

4、 Technical requirements

Technical requirements for silicon core pipe joint

Specification items	32/26	32/28	40/33	46/38
Appearance	The surface is glossy, free of impurities, flash, bubbles, cracks and complete threads.
Material Science	ABS plastic and rubber.
Outer diameter of connecting pipe (mm)	32^+0.8	32^+0.8	40^+1.2	46^+1.5
Sealing test of pipe joint	The temperature is 20 ℃, the pressure is 50 kpa, and it is kept for 24 hours without leakage.
Connecting force of pipe joint (N) (under tightening state)	≥4300	≥4300	≥6700	≥8000

5、 Installation instructions

1. Both ends of the pipe shall be cut flat and cleaned;

2. Assemble and connect according to the connection sequence;

3. Tighten with the special tools provided with this product to ensure that the assembly sequence is correct, and the sealing performance of the joint reaches the best condition when the tightening is in place (note: it is not necessary to use the afterburner during the tightening process);

4. The connector can be disassembled and assembled many times. After a long time of use, disassemble the connector. When reassembling, carefully check the effectiveness of the sealing ring. If any damage is found, replace it again.

Instructions for silicon core tube sealing plug

1、 Purpose

Designed according to JT/T496-2004 and Q/KL012-2005, it is used for sealing both ends of silicon core tube.

2、 Product diagram 1

3、 Composition and material

Assemble the connection according to the connection sequence.

Connection sequence:

Ring nut, washer, rubber sealing ring, ring lug screw

Material Science:

ABS ABS rubber ABS

It consists of four parts in total.

4、 Technical requirements

Technical requirements for sealing plug of silicon core pipe

Specification items	32/28	40/33
Appearance	The inner and outer walls shall be smooth and flat without cracks and obvious marks. The gate and overflow edge shall be trimmed and flat.
Material Science	ABS plastic and rubber
Outer diameter of connecting pipe (mm)	32^+0.3	40^+0.8
Hydrostatic sealing test	The temperature is 20 ℃, the pressure is 50 kpa, and it is kept for 24 hours without leakage.

5、 Installation instructions

1. Both ends of the pipe shall be cut flat and cleaned;

2. Assemble the sealing plug according to the assembly sequence;

3. Loosen the sealing plug and put it into the silicon core tube, and then tighten it to reach the best condition;

4. The sealing plug can be disassembled for many times. After a long time of use, remove the sealing plug. When reassembling, carefully check the effectiveness of each component, and replace it if any damage is found.

Detail display

Keyword:

Communication Tube

Water Supply Pipe

Power Pipe

Special Plastic Pipe

Plastic Pipe Fittings

Categories:

Plastic Pipe Fittings Series